Installation Guide

Pre-Installation Preparation

Before beginning the installation process, it's crucial to properly prepare your workspace and gather all necessary materials. Start by turning off the main water supply to your bathroom and ensuring the area is clear of any obstacles. Remove your existing toilet carefully, taking note of the plumbing configuration and rough-in measurements. The LuxeFlush Pro requires a standard 12-inch rough-in, which is common in most residential bathrooms built after 1980.

Inspect the existing floor flange to ensure it's in good condition and sits flush with or slightly above the finished floor level. If the flange is damaged, cracked, or below floor level, it must be replaced or extended before proceeding with installation. Check that you have access to a GFCI-protected electrical outlet within 3 feet of the toilet location, as required by electrical code for bathroom appliances. The outlet should be rated for at least 15 amps and tested to ensure proper grounding.

Clean the installation area thoroughly, removing any old wax ring residue, debris, or mineral deposits from around the flange. This ensures a proper seal and prevents future leaks. Lay down protective covering on your bathroom floor to prevent scratches or damage during installation. Unpack your LuxeFlush Pro carefully, checking all components against the included parts list. Keep all packaging materials until installation is complete and you've verified everything works correctly.

Review the entire installation manual before starting, familiarizing yourself with each step and the tools required. If you're not comfortable with plumbing or electrical work, this is the time to consider hiring a licensed professional. Many plumbing supply stores and home improvement centers offer installation services, or you can contact our customer support for a list of certified installers in your area. Proper installation is crucial for warranty coverage and optimal performance of your intelligent toilet system.

Required Tools and Materials

Having the right tools on hand before you begin will make the installation process much smoother and help prevent delays. You'll need an adjustable wrench (10-12 inch recommended) for connecting water supply lines and tightening nuts. A screwdriver set with both Phillips and flathead options in various sizes is essential for securing mounting bolts and electrical connections. A hacksaw or tubing cutter will be necessary if you need to cut or adjust the water supply line to the proper length.

A torpedo level or small bubble level ensures your toilet is properly aligned and sits level on the floor, which is critical for proper drainage and operation of the smart features. You'll need a utility knife for cutting and removing the old wax ring and opening packaging. Channel-lock pliers or a basin wrench can be helpful for reaching nuts in tight spaces, particularly when connecting the water supply line. A measuring tape is essential for verifying rough-in dimensions and ensuring proper placement.

In terms of materials, you'll need a new wax ring with a plastic flange (extra-thick recommended for best seal), or alternatively, a modern wax-free toilet seal. Teflon tape (also called plumber's tape) is required for all threaded connections to ensure leak-free joints. Have a bucket, sponge, and old towels ready for cleaning up residual water from the old toilet and for any minor spills during installation. Silicone caulk (clear or white) will be needed for sealing the base of the toilet to the floor, though this should only be applied after confirming the toilet functions properly.

The LuxeFlush Pro package includes most specialized components such as the seat assembly, control panel, remote control, installation hardware, and connection hoses. However, depending on your specific plumbing configuration, you may need additional flexible supply lines, angle stops, or adapters. It's wise to have these common plumbing supplies on hand or readily available from a local hardware store. If you're replacing an old toilet with different mounting hole spacing, you may also need a toilet flange extender or repair kit to properly align with the new fixture.

Step-by-Step Installation Process

Begin by placing the new wax ring on the closet flange, ensuring it's centered and the plastic horn (if present) points upward into the drain opening. Some installers prefer to attach the wax ring to the bottom of the toilet instead of the flange—either method works, but flange placement often provides better control. Carefully lift the LuxeFlush Pro toilet bowl and position it over the flange, aligning the mounting holes with the closet bolts. Lower the toilet straight down onto the wax ring without twisting or shifting, as this can compromise the seal.

Once positioned, press down firmly on the toilet bowl with your full weight, rocking slightly from side to side to compress the wax ring and create a complete seal. Use your level to check that the toilet sits level in both directions—front to back and side to side. If slight adjustments are needed, plastic shims can be inserted under the base, but avoid over-shimming as this can crack the porcelain. Hand-tighten the mounting nuts onto the closet bolts, then use a wrench to snug them down, alternating between sides to ensure even pressure. Be careful not to overtighten, as this can crack the toilet base.

Connect the water supply line to the fill valve on the bottom of the toilet tank, ensuring the rubber washer is properly seated inside the connection. Hand-tighten first, then use a wrench to snug it down another quarter to half turn—overtightening can damage the fitting. Slowly turn on the water supply and carefully inspect all connections for leaks. If you notice any drips, slightly tighten the connection until the leak stops. Allow the tank to fill completely, watching for any overflow or unusual filling behavior.

The electrical connection is the final major step in the installation process. Locate the power cord from the toilet's control unit and plug it into the nearby GFCI outlet. You should hear a brief initialization sound and see indicator lights on the control panel illuminate briefly. Follow the setup wizard on the control panel to configure your preferences including seat temperature, sensor sensitivity, and night light settings. Test each function individually—heated seat, foot sensor flush, self-cleaning cycle, and night light—to ensure everything operates correctly before proceeding to final touches like caulking the base.

Testing and Final Setup

After completing the physical installation, thorough testing is essential to ensure your LuxeFlush Pro operates safely and efficiently. Begin with a comprehensive leak test by flushing the toilet multiple times and carefully inspecting all water connections, the base seal, and tank connections for any signs of moisture. Check the floor around the toilet base after 24 hours of use to confirm the wax ring seal is holding properly. Even small leaks can cause significant water damage over time, so address any issues immediately.

Test all electronic features systematically using the control panel and included remote. Verify that the heated seat reaches and maintains your selected temperature—this may take 10-15 minutes for initial heating. Wave your foot over the sensor area at various heights and distances to confirm the touchless flush responds consistently. Activate the self-cleaning cycle to ensure the UV sterilization system and nozzle cleaning functions operate properly. Test the night light by darkening the bathroom and approaching the toilet to trigger the motion sensor.

Configure your personalized settings using the digital control panel, including preferred seat temperature (typically 95-104°F), water pressure for the cleaning functions, sensor sensitivity levels, and night light brightness. The LuxeFlush Pro remembers up to three user profiles, allowing different family members to have customized preferences. Set up the automatic modes such as power-saving periods when the toilet isn't typically used, and configure the auto-flush delay timing to your preference. Consult the user manual for advanced features like scheduled cleaning cycles and diagnostic mode.

Once you've confirmed everything works correctly, apply a thin bead of silicone caulk around the base of the toilet where it meets the floor, leaving a small gap at the back. This prevents water from spills or cleaning from seeping under the toilet while still allowing any leak from the wax ring to be visible. Smooth the caulk with a wet finger or caulk tool for a professional finish. Allow the caulk to cure for 24 hours before heavy use. Register your product warranty online or by mail within 30 days of installation, and keep all documentation including receipts and installation photos for your records.